STAGE 1 Diesel 1.9 TDI 110hp

Seat Cordoba 1.9 TDI Turbo Diesel 73.5 kW (100 HP) Stage 1

04080120160 10002000300040005000 140 HP +30 295 Nm +60 HP Nm RPM 080160240320
Stock Stage 1 HP / Nm projection
110 140 HP
+30 HP +60 Nm 27% more power

Calibrated ECU file for . Checksum-corrected, ready to flash. Delivered instantly via secure download after payment.

16,293 calibration files in catalog · 9,693 engines · 400+ ECU platforms · Engineering since 2012 · WhatsApp support · < 30 min first response
Performance Projection Engine #7764 · Gains DB
MATCHED ENGINE 1.9 TDI 110hp ASK 1.9L Diesel Stage 1
04080120160 10002000300040005000 140 HP +30 295 Nm +60 HP Nm RPM 080160240320
Stock Stage 1 HP (left) · Nm (right) · Curve shape typical for this ECU family
Real data from Gains API Dyno curve = typical ECU-family projection Final gains depend on fuel, altitude, wear
Required Modifications Stage 1 · Diesel
Hardware
  • No hardware changes required — runs on completely stock hardware
Software / Calibration
  • Boost pressure optimised within factory turbo limits
  • Injection timing & quantity remapped
  • Smoke / EGT limiters refined
  • DTCs left intact, factory safeties preserved

Stage 1 is a software-only calibration. Compatible with stock turbo, injectors, intercooler, exhaust and clutch.

Vehicle & ECU specifications

Exact vehicle, engine and ECU identifiers this calibration file is written for. Cross-check against your ECU before flashing.

Vehicle make Seat
Vehicle model Cordoba
Model year 1999
Displacement 1.9 L
Fuel / Induction Turbo Diesel
Factory power 73.5 kW (100 HP)
ECU manufacturer Bosch
ECU hardware 0281010006
Calibration stage Stage 1
Cylinder capacity 1896 CC
Compression ratio 19,5 : 1
Bore × Stroke 79,5 X 95,5 mm
OEM engine code ASK
File format BIN / ORI
Checksum Pre-corrected (ready to flash)
Delivery Instant download after payment

Engine performance matrix

Power, torque and fuel-economy figures for every tuning stage on this engine, sourced from the tuning-database Gains API. Values are healthy-engine crank numbers; real on-road gains vary with fuel, altitude and mechanical condition.

Engine1.9 TDI 110hp CodeASK Displacement1.9L Capacity1896 CC Compression19,5 : 1 Bore × Stroke79,5 X 95,5 mm FuelDiesel Engine ID#7764
Stage Power Torque Δ HP Δ Nm
Original / Factory 110 HP 235 Nm — —
Stage 1 140 HP 295 Nm +30 (27.3%) +60
Stage 2 147 HP 307 Nm +37 (33.6%) +72
Stage 3 165 HP 364 Nm +55 (50%) +129
Stage 4 198 HP 435 Nm +88 (80%) +200
Fuel economy gain (vs. factory map, same driving profile): combined cycle −8% , full-load cruise −12%. Diesel calibrations typically net bigger combined-cycle savings thanks to shorter duty-cycle on low-load driving.

About this calibration file

The Stage 1 calibration for the 1999 Seat Cordoba 1.9L Turbo Diesel is a drop-in remap that works on completely stock hardware — no turbo, injector, intercooler or fuel-system upgrades required. Injection timing, boost targets, rail-pressure limits and torque maps are rebalanced to extract the safe headroom the OEM leaves untouched for fleet-fuel tolerance, altitude margin and warranty buffer.

This file matches a Bosch ECU with hardware number 0281010006. Verify both identifiers in your flashing tool before writing — an ID mismatch is the most common cause of a bricked ECU. If you are unsure, upload a read of your original file via the file-request wizard and our engineers will confirm compatibility before you flash.

Projected output on a healthy, stock-hardware example of this engine: 140 HP and 295 Nm at the crank — a gain of +30 HP (27%) and +60 Nm over the factory 110 HP / 235 Nm baseline. These numbers are sourced from our Vehicle Performance Database, which aggregates dyno results across this engine family. Real-world gains depend on fuel grade, ambient temperature, mechanical condition and intake/exhaust state.

The file is delivered as a ready-to-flash BIN (and ORI backup where applicable) compatible with all major tools — KESS V2/V3, KTAG, AutoTuner, CMDFlash, Dimsport New Genius, MPPS, Flex, BFlash, PCMFlash, MMFlash — via OBD, bench or boot-mode as supported by your ECU family. Checksums are pre-computed and verified; no additional checksum tool is required. All files include a free revision if post-flash logs reveal a fuelling, boost or EGT issue.

Frequently asked questions

The file is written for the exact ECU hardware 0281010006 (Bosch) listed in the specifications. Read your ECU with any supported tool (KESS, KTAG, AutoTuner, CMD, etc.) and compare the hardware + software numbers against the ones on this page. If they match exactly, the file is a direct fit. If you're not 100% sure, upload your original read via the file-request wizard and our engineers will confirm within minutes — no cost, no obligation.

No. Stage 1 is explicitly a stock-hardware tune — no turbo, injector, fuel-pump, intercooler or exhaust changes are required. The only prerequisite is a mechanically healthy engine with good compression, clean EGR/DPF state, and fresh service fluids.

Re-flashing the ECU leaves a flag that a franchised Seat dealer can detect with their diagnostic tool. Most markets treat this as a basis to deny powertrain warranty claims that the modification could have caused. Emissions-sensitive components (DPF, EGR, SCR) remain fully functional with this calibration — we do not remove, disable or alter any emissions hardware.

The power and torque numbers on this page are healthy-engine crank figures. On a well-maintained 1999 Seat Cordoba running a known-good fuel brand, you should see a clearly perceptible increase in mid-range pull — typically from 1,800 to 4,000 rpm on diesel, 2,500 to 6,000 rpm on petrol — along with a shorter 80-to-120 km/h in-gear time. Thermal performance and fuel consumption depend on how you drive post-tune.

Instant. Immediately after payment clears (typically < 30 seconds on Stripe / PayPal), the download link appears in your account dashboard and is also emailed to you. The link is a signed, expiring URL — download it within 24 hours; if it expires, just re-generate from the dashboard at any time.

Pre-corrected. Every tuning file we sell is processed through CHKSuite (our in-house checksum engine) before it reaches your download link. You can flash it directly with KESS, KTAG, AutoTuner, CMD, Dimsport or any other supported tool — no extra checksum step required. A zero-CRC write to a modern Bosch/Siemens/Delphi ECU bricks the unit, so this is non-negotiable.

Contact us on WhatsApp or through the dashboard support thread. Free revisions are included for the same stage on the same ECU — send us a live log (via VCDS, INPA, EcuConnect, OBDeleven or similar) and we'll adjust timing, boost, rail pressure or smoke limits and re-issue the file. A failed flash itself (write aborted, bricked ECU) is recoverable with our Original file and a bench tool.

This product contains a calibrated Stage1 tuning file for Seat Cordoba 1.9 TDI 1999 Turbodiesel 73.5KW with Bosch 0281010006 and software ID 038906018FB. The base stock vehicle for this calibration has a factory output of around 73.5 kW (~100 HP). This Stage 1 calibration is designed for stock hardware, offering a safe and reliable increase in power and torque for daily use.

All ECU tuning files from TUNING-DATABASE are prepared for professional use. They are useful whenever you search by ECU ID, hardware or software number such as 0281010006, 038906018FB. Use this file for diagnostics, cloning, recovery or as a base for custom remapping.

SHA-256 fingerprint41CD13E7 FE32545B 1B7475D3 B78D5620 AC8E77E6 D01B1F9B 46065F9D AD8AF59D

Related products