STAGE 1

Scania P-R-T 380 12 D PD Turbo Diesel 279.5 kW (380 HP) Motorola Stage 1

Calibrated ECU file for . Checksum-corrected, ready to flash. Delivered instantly via secure download after payment.

16,293 calibration files in catalog · 9,693 engines · 400+ ECU platforms · Engineering since 2012 · WhatsApp support · < 30 min first response

Vehicle & ECU specifications

Exact vehicle, engine and ECU identifiers this calibration file is written for. Cross-check against your ECU before flashing.

Vehicle make Scania
Model year 2008
Fuel / Induction Turbo Diesel
Factory power 279.5 kW (380 HP)
Calibration stage Stage 1
File format BIN / ORI
Checksum Pre-corrected (ready to flash)
Delivery Instant download after payment

About this calibration file

The Stage 1 calibration for the 2008 Scania Turbo Diesel is a drop-in remap that works on completely stock hardware — no turbo, injector, intercooler or fuel-system upgrades required. Injection timing, boost targets, rail-pressure limits and torque maps are rebalanced to extract the safe headroom the OEM leaves untouched for fleet-fuel tolerance, altitude margin and warranty buffer.

This file matches a OEM ECU. Verify both identifiers in your flashing tool before writing — an ID mismatch is the most common cause of a bricked ECU. If you are unsure, upload a read of your original file via the file-request wizard and our engineers will confirm compatibility before you flash.

The file is delivered as a ready-to-flash BIN (and ORI backup where applicable) compatible with all major tools — KESS V2/V3, KTAG, AutoTuner, CMDFlash, Dimsport New Genius, MPPS, Flex, BFlash, PCMFlash, MMFlash — via OBD, bench or boot-mode as supported by your ECU family. Checksums are pre-computed and verified; no additional checksum tool is required. All files include a free revision if post-flash logs reveal a fuelling, boost or EGT issue.

Frequently asked questions

The file is written for the exact ECU hardware listed in the specifications. Read your ECU with any supported tool (KESS, KTAG, AutoTuner, CMD, etc.) and compare the hardware + software numbers against the ones on this page. If they match exactly, the file is a direct fit. If you're not 100% sure, upload your original read via the file-request wizard and our engineers will confirm within minutes — no cost, no obligation.

No. Stage 1 is explicitly a stock-hardware tune — no turbo, injector, fuel-pump, intercooler or exhaust changes are required. The only prerequisite is a mechanically healthy engine with good compression, clean EGR/DPF state, and fresh service fluids.

Re-flashing the ECU leaves a flag that a franchised Scania dealer can detect with their diagnostic tool. Most markets treat this as a basis to deny powertrain warranty claims that the modification could have caused. Emissions-sensitive components (DPF, EGR, SCR) remain fully functional with this calibration — we do not remove, disable or alter any emissions hardware.

The power and torque numbers on this page are healthy-engine crank figures. On a well-maintained 2008 Scania running a known-good fuel brand, you should see a clearly perceptible increase in mid-range pull — typically from 1,800 to 4,000 rpm on diesel, 2,500 to 6,000 rpm on petrol — along with a shorter 80-to-120 km/h in-gear time. Thermal performance and fuel consumption depend on how you drive post-tune.

Instant. Immediately after payment clears (typically < 30 seconds on Stripe / PayPal), the download link appears in your account dashboard and is also emailed to you. The link is a signed, expiring URL — download it within 24 hours; if it expires, just re-generate from the dashboard at any time.

Pre-corrected. Every tuning file we sell is processed through CHKSuite (our in-house checksum engine) before it reaches your download link. You can flash it directly with KESS, KTAG, AutoTuner, CMD, Dimsport or any other supported tool — no extra checksum step required. A zero-CRC write to a modern Bosch/Siemens/Delphi ECU bricks the unit, so this is non-negotiable.

Contact us on WhatsApp or through the dashboard support thread. Free revisions are included for the same stage on the same ECU — send us a live log (via VCDS, INPA, EcuConnect, OBDeleven or similar) and we'll adjust timing, boost, rail pressure or smoke limits and re-issue the file. A failed flash itself (write aborted, bricked ECU) is recoverable with our Original file and a bench tool.

This product contains a calibrated Stage1 tuning file for Scania P-R-T 380 12 D PD 2008 Turbodiesel 279.5KW with Motorola . The base stock vehicle for this calibration has a factory output of around 279.5 kW (~380 HP). This Stage 1 calibration is designed for stock hardware, offering a safe and reliable increase in power and torque for daily use.

All ECU tuning files from TUNING-DATABASE are prepared for professional use. They are useful whenever you search by ECU ID, hardware or software number the ECU part number in the product title.Use this file for diagnostics, cloning, recovery or as a base for custom remapping.

SHA-256 fingerprint4847EE86 51861EAD 08EAE65F ED8F4AD2 7F0A7F8F 49172358 40C894CC EC673A9C

Related products