STAGE 1 Diesel 1.5 Ecoblue 75hp

Ford Connect 1.8 TDCi Turbo Diesel 55.2 kW (75 HP) Stage 1

0306090120 10002000300040005000 110 HP +35 270 Nm +50 HP Nm RPM 080160240
Stock Stage 1 HP / Nm projection
75 110 HP
+35 HP +50 Nm 47% more power

Calibrated ECU file for . Checksum-corrected, ready to flash. Delivered instantly via secure download after payment.

16,293 calibration files in catalog · 9,693 engines · 400+ ECU platforms · Engineering since 2012 · WhatsApp support · < 30 min first response
Performance Projection Engine #3412 · Gains DB
MATCHED ENGINE 1.5 Ecoblue 75hp 1.5 Ecoblue 75hp 1.5L Diesel Stage 1
0306090120 10002000300040005000 110 HP +35 270 Nm +50 HP Nm RPM 080160240
Stock Stage 1 HP (left) · Nm (right) · Curve shape typical for this ECU family
Real data from Gains API Dyno curve = typical ECU-family projection Final gains depend on fuel, altitude, wear

Vehicle & ECU specifications

Exact vehicle, engine and ECU identifiers this calibration file is written for. Cross-check against your ECU before flashing.

Vehicle make Ford
Vehicle model Connect
Model year 2007
Displacement 1.8 L
Fuel / Induction Turbo Diesel
Factory power 55.2 kW (75 HP)
ECU manufacturer Siemens
ECU hardware CAFR1340FR13400
Calibration stage Stage 1
Cylinder capacity 1499 CC
Compression ratio 16,0 : 1
Bore × Stroke 73,5 X 88,3 mm
OEM engine code 1.5 Ecoblue 75hp
File format BIN / ORI
Checksum Pre-corrected (ready to flash)
Delivery Instant download after payment

Engine performance matrix

Power, torque and fuel-economy figures for every tuning stage on this engine, sourced from the tuning-database Gains API. Values are healthy-engine crank numbers; real on-road gains vary with fuel, altitude and mechanical condition.

Engine1.5 Ecoblue 75hp Code1.5 Ecoblue 75hp Displacement1.5L Capacity1499 CC Compression16,0 : 1 Bore × Stroke73,5 X 88,3 mm FuelDiesel Engine ID#3412
Stage Power Torque Δ HP Δ Nm
Original / Factory 75 HP 220 Nm — —
Stage 1 110 HP 270 Nm +35 (46.7%) +50
Fuel economy gain (vs. factory map, same driving profile): combined cycle −8% , full-load cruise −12%. Diesel calibrations typically net bigger combined-cycle savings thanks to shorter duty-cycle on low-load driving.

About this calibration file

The Stage 1 calibration for the 2007 Ford Connect 1.8L Turbo Diesel is a drop-in remap that works on completely stock hardware — no turbo, injector, intercooler or fuel-system upgrades required. Injection timing, boost targets, rail-pressure limits and torque maps are rebalanced to extract the safe headroom the OEM leaves untouched for fleet-fuel tolerance, altitude margin and warranty buffer.

This file matches a Siemens ECU with hardware number CAFR1340FR13400. Verify both identifiers in your flashing tool before writing — an ID mismatch is the most common cause of a bricked ECU. If you are unsure, upload a read of your original file via the file-request wizard and our engineers will confirm compatibility before you flash.

Projected output on a healthy, stock-hardware example of this engine: 110 HP and 270 Nm at the crank — a gain of +35 HP (47%) and +50 Nm over the factory 75 HP / 220 Nm baseline. These numbers are sourced from our Vehicle Performance Database, which aggregates dyno results across this engine family. Real-world gains depend on fuel grade, ambient temperature, mechanical condition and intake/exhaust state.

The file is delivered as a ready-to-flash BIN (and ORI backup where applicable) compatible with all major tools — KESS V2/V3, KTAG, AutoTuner, CMDFlash, Dimsport New Genius, MPPS, Flex, BFlash, PCMFlash, MMFlash — via OBD, bench or boot-mode as supported by your ECU family. Checksums are pre-computed and verified; no additional checksum tool is required. All files include a free revision if post-flash logs reveal a fuelling, boost or EGT issue.

Frequently asked questions

The file is written for the exact ECU hardware CAFR1340FR13400 (Siemens) listed in the specifications. Read your ECU with any supported tool (KESS, KTAG, AutoTuner, CMD, etc.) and compare the hardware + software numbers against the ones on this page. If they match exactly, the file is a direct fit. If you're not 100% sure, upload your original read via the file-request wizard and our engineers will confirm within minutes — no cost, no obligation.

No. Stage 1 is explicitly a stock-hardware tune — no turbo, injector, fuel-pump, intercooler or exhaust changes are required. The only prerequisite is a mechanically healthy engine with good compression, clean EGR/DPF state, and fresh service fluids.

Re-flashing the ECU leaves a flag that a franchised Ford dealer can detect with their diagnostic tool. Most markets treat this as a basis to deny powertrain warranty claims that the modification could have caused. Emissions-sensitive components (DPF, EGR, SCR) remain fully functional with this calibration — we do not remove, disable or alter any emissions hardware.

The power and torque numbers on this page are healthy-engine crank figures. On a well-maintained 2007 Ford Connect running a known-good fuel brand, you should see a clearly perceptible increase in mid-range pull — typically from 1,800 to 4,000 rpm on diesel, 2,500 to 6,000 rpm on petrol — along with a shorter 80-to-120 km/h in-gear time. Thermal performance and fuel consumption depend on how you drive post-tune.

Instant. Immediately after payment clears (typically < 30 seconds on Stripe / PayPal), the download link appears in your account dashboard and is also emailed to you. The link is a signed, expiring URL — download it within 24 hours; if it expires, just re-generate from the dashboard at any time.

Pre-corrected. Every tuning file we sell is processed through CHKSuite (our in-house checksum engine) before it reaches your download link. You can flash it directly with KESS, KTAG, AutoTuner, CMD, Dimsport or any other supported tool — no extra checksum step required. A zero-CRC write to a modern Bosch/Siemens/Delphi ECU bricks the unit, so this is non-negotiable.

Contact us on WhatsApp or through the dashboard support thread. Free revisions are included for the same stage on the same ECU — send us a live log (via VCDS, INPA, EcuConnect, OBDeleven or similar) and we'll adjust timing, boost, rail pressure or smoke limits and re-issue the file. A failed flash itself (write aborted, bricked ECU) is recoverable with our Original file and a bench tool.

This product contains a calibrated Stage1 tuning file for Ford Connect 1.8 TDCi 2007 Turbodiesel 55.2KW with Siemens CAFR1340FR13400 and software ID FR1D034000000. The base stock vehicle for this calibration has a factory output of around 55.2 kW (~75 HP). This Stage 1 calibration is designed for stock hardware, offering a safe and reliable increase in power and torque for daily use.

All ECU tuning files from TUNING-DATABASE are prepared for professional use. They are useful whenever you search by ECU ID, hardware or software number such as CAFR1340FR13400, FR1D034000000. Use this file for diagnostics, cloning, recovery or as a base for custom remapping.

SHA-256 fingerprintC9B522A1 A7E4A2B2 48E1E1C3 7DA79CEA F36718AE FDD94C93 4A7CBA63 7F3C4C87

Same engine — other calibrations

Alternative stages for the same ECU: Ford family