STAGE 2

BMW E30 325i Petrol 125.8 kW (171 HP) Stage 2

Calibrated ECU file for . Checksum-corrected, ready to flash. Delivered instantly via secure download after payment.

16,293 calibration files in catalog · 9,693 engines · 400+ ECU platforms · Engineering since 2012 · WhatsApp support · < 30 min first response

Vehicle & ECU specifications

Exact vehicle, engine and ECU identifiers this calibration file is written for. Cross-check against your ECU before flashing.

Vehicle make BMW
Vehicle model E30 325i
Model year 2004
Fuel / Induction Petrol
Factory power 125.8 kW (171 HP)
ECU manufacturer Bosch
ECU hardware 0261200173
Calibration stage Stage 2
Cylinder capacity 1991 CC
Compression ratio 11,0 : 1
Bore × Stroke 80,0 X 66,0 mm
OEM engine code M54B22
File format BIN / ORI
Checksum Pre-corrected (ready to flash)
Delivery Instant download after payment

Engine performance matrix

Power, torque and fuel-economy figures for every tuning stage on this engine, sourced from the tuning-database Gains API. Values are healthy-engine crank numbers; real on-road gains vary with fuel, altitude and mechanical condition.

Engine320i 170hp CodeM54B22 Displacement2L Capacity1991 CC Compression11,0 : 1 Bore × Stroke80,0 X 66,0 mm FuelPetrol Engine ID#925
Stage Power Torque Δ HP Δ Nm
Original / Factory 170 HP 210 Nm — —
Stage 1 185 HP 230 Nm +15 (8.8%) +20
Fuel economy gain (vs. factory map, same driving profile): combined cycle −8% , full-load cruise −12%. Diesel calibrations typically net bigger combined-cycle savings thanks to shorter duty-cycle on low-load driving.

About this calibration file

The Stage 2 calibration for the 2004 BMW E30 325i Petrol is written for vehicles with supporting bolt-ons: a higher-flow downpipe or sports catalyst, upgraded intercooler and upgraded intake are recommended. Boost targets, fuel-rail pressure, injector duration and VGT positioning are pushed further than a Stage 1 map while keeping exhaust-gas temperatures inside safe bands.

This file matches a Bosch ECU with hardware number 0261200173. Verify both identifiers in your flashing tool before writing — an ID mismatch is the most common cause of a bricked ECU. If you are unsure, upload a read of your original file via the file-request wizard and our engineers will confirm compatibility before you flash.

The file is delivered as a ready-to-flash BIN (and ORI backup where applicable) compatible with all major tools — KESS V2/V3, KTAG, AutoTuner, CMDFlash, Dimsport New Genius, MPPS, Flex, BFlash, PCMFlash, MMFlash — via OBD, bench or boot-mode as supported by your ECU family. Checksums are pre-computed and verified; no additional checksum tool is required. All files include a free revision if post-flash logs reveal a fuelling, boost or EGT issue.

Frequently asked questions

The file is written for the exact ECU hardware 0261200173 (Bosch) listed in the specifications. Read your ECU with any supported tool (KESS, KTAG, AutoTuner, CMD, etc.) and compare the hardware + software numbers against the ones on this page. If they match exactly, the file is a direct fit. If you're not 100% sure, upload your original read via the file-request wizard and our engineers will confirm within minutes — no cost, no obligation.

Stage 2 benefits from a higher-flow downpipe or sports catalyst, an upgraded intercooler on forced-induction engines, and in some cases a cooler intake. The map will run on stock hardware but will not reach the quoted figures without the supporting bolt-ons.

Re-flashing the ECU leaves a flag that a franchised BMW dealer can detect with their diagnostic tool. Most markets treat this as a basis to deny powertrain warranty claims that the modification could have caused. Emissions-sensitive components (DPF, EGR, SCR) remain fully functional with this calibration — we do not remove, disable or alter any emissions hardware.

The power and torque numbers on this page are healthy-engine crank figures. On a well-maintained 2004 BMW E30 325i running a known-good fuel brand, you should see a clearly perceptible increase in mid-range pull — typically from 1,800 to 4,000 rpm on diesel, 2,500 to 6,000 rpm on petrol — along with a shorter 80-to-120 km/h in-gear time. Thermal performance and fuel consumption depend on how you drive post-tune.

Instant. Immediately after payment clears (typically < 30 seconds on Stripe / PayPal), the download link appears in your account dashboard and is also emailed to you. The link is a signed, expiring URL — download it within 24 hours; if it expires, just re-generate from the dashboard at any time.

Pre-corrected. Every tuning file we sell is processed through CHKSuite (our in-house checksum engine) before it reaches your download link. You can flash it directly with KESS, KTAG, AutoTuner, CMD, Dimsport or any other supported tool — no extra checksum step required. A zero-CRC write to a modern Bosch/Siemens/Delphi ECU bricks the unit, so this is non-negotiable.

Contact us on WhatsApp or through the dashboard support thread. Free revisions are included for the same stage on the same ECU — send us a live log (via VCDS, INPA, EcuConnect, OBDeleven or similar) and we'll adjust timing, boost, rail pressure or smoke limits and re-issue the file. A failed flash itself (write aborted, bricked ECU) is recoverable with our Original file and a bench tool.

This product contains a calibrated Stage2 tuning file for BMW E30 325i 2004 Benzin 125.8KW with Bosch 0261200173. The base stock vehicle for this calibration has a factory output of around 125.8 kW (~171 HP). Stage 2 is intended for cars with supporting modifications (exhaust, intake, intercooler) and delivers a stronger performance gain.

All ECU tuning files from TUNING-DATABASE are prepared for professional use. They are useful whenever you search by ECU ID, hardware or software number such as 0261200173. Use this file for diagnostics, cloning, recovery or as a base for custom remapping.

SHA-256 fingerprint93514FB3 26798635 F1895721 717D8CEB 27670934 9CA812EA 3DC3B1E1 7D974759

Same engine — other calibrations

Alternative stages for the same ECU: BMW family