STAGE 1 Diesel 2.9 CRDi 150hp

Hyundai Terracan 2.9 CRDi Turbo Diesel 105.9 kW (144 HP) Stage 1

050100150200 10002000300040005000 180 HP +30 390 Nm +57 HP Nm RPM 0100200300400
Stock Stage 1 HP / Nm projection
150 180 HP
+30 HP +57 Nm 20% more power

Calibrated ECU file for . Checksum-corrected, ready to flash. Delivered instantly via secure download after payment.

16,293 calibration files in catalog · 9,693 engines · 400+ ECU platforms · Engineering since 2012 · WhatsApp support · < 30 min first response
Performance Projection Engine #3783 · Gains DB
MATCHED ENGINE 2.9 CRDi 150hp J3 CR 2.9L Diesel Stage 1
050100150200 10002000300040005000 180 HP +30 390 Nm +57 HP Nm RPM 0100200300400
Stock Stage 1 HP (left) · Nm (right) · Curve shape typical for this ECU family
Real data from Gains API Dyno curve = typical ECU-family projection Final gains depend on fuel, altitude, wear
Required Modifications Stage 1 · Diesel
Hardware
  • No hardware changes required — runs on completely stock hardware
Software / Calibration
  • Boost pressure optimised within factory turbo limits
  • Injection timing & quantity remapped
  • Smoke / EGT limiters refined
  • DTCs left intact, factory safeties preserved

Stage 1 is a software-only calibration. Compatible with stock turbo, injectors, intercooler, exhaust and clutch.

Vehicle & ECU specifications

Exact vehicle, engine and ECU identifiers this calibration file is written for. Cross-check against your ECU before flashing.

Vehicle make Hyundai
Vehicle model Terracan
Displacement 2.9 L
Fuel / Induction Turbo Diesel
Factory power 105.9 kW (144 HP)
ECU manufacturer Bosch
Calibration stage Stage 1
Cylinder capacity 2902 CC
Compression ratio 19,3 : 1
Bore × Stroke 97,1 X 98,0 mm
OEM engine code J3 CR
File format BIN / ORI
Checksum Pre-corrected (ready to flash)
Delivery Instant download after payment

Engine performance matrix

Power, torque and fuel-economy figures for every tuning stage on this engine, sourced from the tuning-database Gains API. Values are healthy-engine crank numbers; real on-road gains vary with fuel, altitude and mechanical condition.

Engine2.9 CRDi 150hp CodeJ3 CR Displacement2.9L Capacity2902 CC Compression19,3 : 1 Bore × Stroke97,1 X 98,0 mm FuelDiesel Engine ID#3783
Stage Power Torque Δ HP Δ Nm
Original / Factory 150 HP 333 Nm — —
Stage 1 180 HP 390 Nm +30 (20%) +57
Stage 2 189 HP 406 Nm +39 (26%) +73
Stage 3 225 HP 516 Nm +75 (50%) +183
Stage 4 270 HP 616 Nm +120 (80%) +283
Fuel economy gain (vs. factory map, same driving profile): combined cycle −8% , full-load cruise −12%. Diesel calibrations typically net bigger combined-cycle savings thanks to shorter duty-cycle on low-load driving.

About this calibration file

The Stage 1 calibration for the Hyundai Terracan 2.9L Turbo Diesel is a drop-in remap that works on completely stock hardware — no turbo, injector, intercooler or fuel-system upgrades required. Injection timing, boost targets, rail-pressure limits and torque maps are rebalanced to extract the safe headroom the OEM leaves untouched for fleet-fuel tolerance, altitude margin and warranty buffer.

This file matches a Bosch ECU. Verify both identifiers in your flashing tool before writing — an ID mismatch is the most common cause of a bricked ECU. If you are unsure, upload a read of your original file via the file-request wizard and our engineers will confirm compatibility before you flash.

Projected output on a healthy, stock-hardware example of this engine: 180 HP and 390 Nm at the crank — a gain of +30 HP (20%) and +57 Nm over the factory 150 HP / 333 Nm baseline. These numbers are sourced from our Vehicle Performance Database, which aggregates dyno results across this engine family. Real-world gains depend on fuel grade, ambient temperature, mechanical condition and intake/exhaust state.

The file is delivered as a ready-to-flash BIN (and ORI backup where applicable) compatible with all major tools — KESS V2/V3, KTAG, AutoTuner, CMDFlash, Dimsport New Genius, MPPS, Flex, BFlash, PCMFlash, MMFlash — via OBD, bench or boot-mode as supported by your ECU family. Checksums are pre-computed and verified; no additional checksum tool is required. All files include a free revision if post-flash logs reveal a fuelling, boost or EGT issue.

Frequently asked questions

The file is written for the exact ECU hardware (Bosch) listed in the specifications. Read your ECU with any supported tool (KESS, KTAG, AutoTuner, CMD, etc.) and compare the hardware + software numbers against the ones on this page. If they match exactly, the file is a direct fit. If you're not 100% sure, upload your original read via the file-request wizard and our engineers will confirm within minutes — no cost, no obligation.

No. Stage 1 is explicitly a stock-hardware tune — no turbo, injector, fuel-pump, intercooler or exhaust changes are required. The only prerequisite is a mechanically healthy engine with good compression, clean EGR/DPF state, and fresh service fluids.

Re-flashing the ECU leaves a flag that a franchised Hyundai dealer can detect with their diagnostic tool. Most markets treat this as a basis to deny powertrain warranty claims that the modification could have caused. Emissions-sensitive components (DPF, EGR, SCR) remain fully functional with this calibration — we do not remove, disable or alter any emissions hardware.

The power and torque numbers on this page are healthy-engine crank figures. On a well-maintained Hyundai Terracan running a known-good fuel brand, you should see a clearly perceptible increase in mid-range pull — typically from 1,800 to 4,000 rpm on diesel, 2,500 to 6,000 rpm on petrol — along with a shorter 80-to-120 km/h in-gear time. Thermal performance and fuel consumption depend on how you drive post-tune.

Instant. Immediately after payment clears (typically < 30 seconds on Stripe / PayPal), the download link appears in your account dashboard and is also emailed to you. The link is a signed, expiring URL — download it within 24 hours; if it expires, just re-generate from the dashboard at any time.

Pre-corrected. Every tuning file we sell is processed through CHKSuite (our in-house checksum engine) before it reaches your download link. You can flash it directly with KESS, KTAG, AutoTuner, CMD, Dimsport or any other supported tool — no extra checksum step required. A zero-CRC write to a modern Bosch/Siemens/Delphi ECU bricks the unit, so this is non-negotiable.

Contact us on WhatsApp or through the dashboard support thread. Free revisions are included for the same stage on the same ECU — send us a live log (via VCDS, INPA, EcuConnect, OBDeleven or similar) and we'll adjust timing, boost, rail pressure or smoke limits and re-issue the file. A failed flash itself (write aborted, bricked ECU) is recoverable with our Original file and a bench tool.

This product contains a calibrated Stage1 tuning file for Hyundai Terracan 2.9 CRDi Turbodiesel 105.9KW with Bosch C7H40H1 and software ID C7H40H1. The base stock vehicle for this calibration has a factory output of around 105.9 kW (~144 HP). This Stage 1 calibration is designed for stock hardware, offering a safe and reliable increase in power and torque for daily use.

All ECU tuning files from TUNING-DATABASE are prepared for professional use. They are useful whenever you search by ECU ID, hardware or software number such as C7H40H1, C7H40H1. Use this file for diagnostics, cloning, recovery or as a base for custom remapping.

SHA-256 fingerprint5A19D7AA BC7E6A4E D1742F76 E492E181 B0EECCAE 0F084D98 AA3DD174 AB95E058

Same engine — other calibrations

Alternative stages for the same ECU: Hyundai family