STAGE 1

Volvo V40 LPT Turbo Petrol 117.7 kW (160 HP) Stage 1

Calibrated ECU file for . Checksum-corrected, ready to flash. Delivered instantly via secure download after payment.

16,293 calibration files in catalog · 9,693 engines · 400+ ECU platforms · Engineering since 2012 · WhatsApp support · < 30 min first response

Vehicle & ECU specifications

Exact vehicle, engine and ECU identifiers this calibration file is written for. Cross-check against your ECU before flashing.

Vehicle make Volvo
Vehicle model V40 Lpt
Fuel / Induction Petrol
Factory power 117.7 kW (160 HP)
ECU manufacturer Siemens
ECU hardware V411043000000
Calibration stage Stage 1
OEM engine code 200d (2.0d) 160hp
File format BIN / ORI
Checksum Pre-corrected (ready to flash)
Delivery Instant download after payment

Engine performance matrix

Power, torque and fuel-economy figures for every tuning stage on this engine, sourced from the tuning-database Gains API. Values are healthy-engine crank numbers; real on-road gains vary with fuel, altitude and mechanical condition.

Engine200d (2.0d) 160hp Code200d (2.0d) 160hp Displacement2.0L FuelPetrol Engine ID#5299
Stage Power Torque Δ HP Δ Nm
Original / Factory 160 HP 0 Nm — —
Fuel economy gain (vs. factory map, same driving profile): combined cycle −8% , full-load cruise −12%. Diesel calibrations typically net bigger combined-cycle savings thanks to shorter duty-cycle on low-load driving.

About this calibration file

The Stage 1 calibration for the Volvo V40 Lpt Petrol is a drop-in remap that works on completely stock hardware — no turbo, injector, intercooler or fuel-system upgrades required. Injection timing, boost targets, rail-pressure limits and torque maps are rebalanced to extract the safe headroom the OEM leaves untouched for fleet-fuel tolerance, altitude margin and warranty buffer.

This file matches a Siemens ECU with hardware number V411043000000. Verify both identifiers in your flashing tool before writing — an ID mismatch is the most common cause of a bricked ECU. If you are unsure, upload a read of your original file via the file-request wizard and our engineers will confirm compatibility before you flash.

The file is delivered as a ready-to-flash BIN (and ORI backup where applicable) compatible with all major tools — KESS V2/V3, KTAG, AutoTuner, CMDFlash, Dimsport New Genius, MPPS, Flex, BFlash, PCMFlash, MMFlash — via OBD, bench or boot-mode as supported by your ECU family. Checksums are pre-computed and verified; no additional checksum tool is required. All files include a free revision if post-flash logs reveal a fuelling, boost or EGT issue.

Frequently asked questions

The file is written for the exact ECU hardware V411043000000 (Siemens) listed in the specifications. Read your ECU with any supported tool (KESS, KTAG, AutoTuner, CMD, etc.) and compare the hardware + software numbers against the ones on this page. If they match exactly, the file is a direct fit. If you're not 100% sure, upload your original read via the file-request wizard and our engineers will confirm within minutes — no cost, no obligation.

No. Stage 1 is explicitly a stock-hardware tune — no turbo, injector, fuel-pump, intercooler or exhaust changes are required. The only prerequisite is a mechanically healthy engine with good compression, clean EGR/DPF state, and fresh service fluids.

Re-flashing the ECU leaves a flag that a franchised Volvo dealer can detect with their diagnostic tool. Most markets treat this as a basis to deny powertrain warranty claims that the modification could have caused. Emissions-sensitive components (DPF, EGR, SCR) remain fully functional with this calibration — we do not remove, disable or alter any emissions hardware.

The power and torque numbers on this page are healthy-engine crank figures. On a well-maintained Volvo V40 Lpt running a known-good fuel brand, you should see a clearly perceptible increase in mid-range pull — typically from 1,800 to 4,000 rpm on diesel, 2,500 to 6,000 rpm on petrol — along with a shorter 80-to-120 km/h in-gear time. Thermal performance and fuel consumption depend on how you drive post-tune.

Instant. Immediately after payment clears (typically < 30 seconds on Stripe / PayPal), the download link appears in your account dashboard and is also emailed to you. The link is a signed, expiring URL — download it within 24 hours; if it expires, just re-generate from the dashboard at any time.

Pre-corrected. Every tuning file we sell is processed through CHKSuite (our in-house checksum engine) before it reaches your download link. You can flash it directly with KESS, KTAG, AutoTuner, CMD, Dimsport or any other supported tool — no extra checksum step required. A zero-CRC write to a modern Bosch/Siemens/Delphi ECU bricks the unit, so this is non-negotiable.

Contact us on WhatsApp or through the dashboard support thread. Free revisions are included for the same stage on the same ECU — send us a live log (via VCDS, INPA, EcuConnect, OBDeleven or similar) and we'll adjust timing, boost, rail pressure or smoke limits and re-issue the file. A failed flash itself (write aborted, bricked ECU) is recoverable with our Original file and a bench tool.

This product contains a calibrated Stage1 tuning file for Volvo V40 LPT Turbo-Benzin 117.7KW with Siemens V411043000000. The base stock vehicle for this calibration has a factory output of around 117.7 kW (~160 HP). This Stage 1 calibration is designed for stock hardware, offering a safe and reliable increase in power and torque for daily use.

All ECU tuning files from TUNING-DATABASE are prepared for professional use. They are useful whenever you search by ECU ID, hardware or software number such as V411043000000. Use this file for diagnostics, cloning, recovery or as a base for custom remapping.

SHA-256 fingerprintD3D1D0E5 8B645671 1B0F9898 2F6A5D82 D2AC90EB 6C8D9B44 17A18EFB 07A44A2B

Same engine — other calibrations

Alternative stages for the same ECU: Mercedes-Benz family